menu arrow_back baolong24's Share Disk chevron_right ROM chevron_right Razer Phone chevron_right TWRP
  • brightness_4深色模式
  • home Home
  • code
    Github
  • info
    关于该主题
  • 登录
    lock
    faceREADME.md
    ## TWRP 3.4.0-0 For Razer Phone
    
    ## 安装向导/Install Instructions
    请仔细阅读向导,并安装向导刷入。如果不这样做,可能会导致今后无法使用设备,并且没有9008线刷包可用。
    ######
    Read these instructions and follow them carefully. Failure to do so may result in not being able to update the device in the future and there are no factory images available.
    ######
    雷蛇手机采用了较新的AB分区方案,这种方案首次在Pixel 1上推出。这种方案没有恢复分区。Recovery 是 Boot 镜像的一部分。与 Pixel 设备不同的是,雷蛇禁用了从 Bootloader 直接启动 Boot 镜像,所以没有办法临时启动 TWRP 来进行安装。
    ######
    The Razer Phone uses the newer AB partition scheme first introduced on the Pixel 1. As such there is no recovery partition. Instead, the recovery is part of the boot image. Unlike the Pixel devices, Razer has disabled fastboot boot so there is no way to temporarily boot TWRP to perform an installation.
    ######
    在雷蛇手机上进入 Bootloader 或 Recovery 需要将设备连接到电脑。我建议不要在没有电脑的时候进行此操作,不然你无法在出现问题时回到恢复模式。
    关闭设备电源。按住音量向上进入 Recovery,或按住音量向下进入 Bootlaoder。在按住相应按钮的同时插入设备,设备会启动到相应的模式。
    如果您看到了充电的图标,请尝试不同的USB电缆或端口。
    ######
    Getting into fastboot mode or recovery on the Razer Phone requires plugging the device into a USB cable. I would recommend against flashing or performing recovery-related actions unless you have access to a USB cable and port so that you can get back into recovery should something go wrong. Power off the device. Hold volume up to get into recovery or volume down to get into fastboot mode. Plug the device in while holding the appropriate button and the device should boot to the mode you selected. If it boots up to the charging screen, try a different USB cable or port. Make sure you are able to boot the device to fastboot via USB cable before flashing anything.
    ######
    ######
    我们将使用另一个另一个 A/B 分区来刷入 TWRP 的 img 镜像并启动 TWRP。要做到这一点,你需要打开开发者选项并启用 USB 调试。您还需要启用 OEM 解锁并解锁 Bootloader。我不会说明如何安装驱动程序,也不会协助你完成这些基本步骤。如果你需要的话,这些东西在百度上可以搜到。
    解锁 Bootloader 需要使用 `fastboot flashing unlock`,而不是 `fastboot oem unlock`
    当 adb 可以工作时,运行这个命令。`adb shell getprop ro.boot.slot_suffix`。
    ######
    We are going to use the other boot slot to flash the initial copy of TWRP and boot TWRP. To do this you will need to turn on developer options and enable USB debugging. You will also need to enable OEM unlocking and unlock the bootloader. I am not going to discuss how to get the proper drivers installed or assist you with doing these basic steps. There's tons of guides elsewhere for these items if you need it. I will say that unlocking the bootloader requires using fastboot flashing unlock instead of fastboot oem unlock. Once you have adb working, run this command: `adb shell getprop ro.boot.slot_suffix`
    ######
    他应该会显示 `[ro.boot.slot_suffix]: [_a]` 或者 `[ro.boot.slot_suffix]: [_b]`
    ######
    It should say: `[ro.boot.slot_suffix]: [_a]` Or: `[ro.boot.slot_suffix]: [_b]`
    ######
    请记住您当前使用的是A还是B。
    关机,将数据线连接到电脑的同时按住音量降低键启动到 Bootloader。你需要切换到另一个 A/B 分区。如果你目前使用的是分区 A,运行:`fastboot --set-active=_b` 反之运行:`fastboot --set-active=_a`
    ######
    Make note of whether you are currently using slot A or B. Next power off the device and boot to the bootloader using your USB cable and volume down. You want to switch to the other boot slot. If you are currently on slot A, type this: fastboot --set-active=_b Or on slot B type this: fastboot --set-active=_a
    ######
    他应该会显示: `Setting current slot to 'a'... OKAY [ 0.042s] finished. total time: 0.042s`
    ######
    You should see something like this: `Setting current slot to 'a'... OKAY [ 0.042s] finished. total time: 0.042s`
    ######
    ######
    Once it's on the right boot slot, type this: `fastboot flash boot twrp-3.2.1-0-cheryl.img && fastboot reboot`
    ######